Enquire
+44 (0)1753 549 360
Home
You are here : Information & Advice : Fitting Wire Wheels
About MWS
MWS Wire Wheels
Fitting Wire Wheels
Fitment Guide
Technical information
News
Gallery
Methods of Payment
Delivery Information
Terms and Conditions
FAQ

Fitting Wire Wheels


 
Please use the Fitment Guide to establish the correct parts for your car

 

Fitting Centre-lock Wire Wheels


Fitting Centre-Lock Wire Wheels Diagram

 


There may be some vehicles, usually kit cars or replicas, that wheels can be supplied for based on their running gear but are not listed in the Fitment Guide; please contact us to discuss your requirements.

A centre-lock wire wheel is fitted onto a car axle using a splined hub; the splines (or serrations) of the hub lock with the splines on the inside of the wheel centre to produce drive. Splined hubs may be integral fitting or bolt-on. Please refer to the vehicle's service manual for instructions on fitting integral splines. The diagram below illustrates fitting bolt-on hubs.


Fitting Bolt-On Hubs Diagram

When putting a centre-lock wheel onto a splined hub, the splined area inside of the wheel centre must be greased to ease the wheel on and prevent the two surfaces corroding together. All new MWS centre-lock wheels from stock are provided pre-greased; ready to go on the car.  If a stock wheel has been repainted then as part of the process it has to be degreased and it will need fresh grease applying before fitting to the vehicle.

The wheel is secured onto the hub with a spinner (knock-on centre cap). The spinner should always tighten towards the rear of the vehicle; this ensures that as the wheel turns whilst driving the spinner tightens and locks into place.
 
A spinner spanner is required to apply/remove spinners without ears, such as octagonal (Continental) or Federal. The spanner fits over the spinner and is tightened/loosened with a hammer. MWS can supply the following spinner spanners:
 

 

Two-eared and three-eared spinners can be applied/removed by using a copper and hide hammer or soft-blow plastic hammer directly onto the ears of the spinner. MWS recommends using a wooden spinner saver for two-eared spinners.
 


 

Do not over-tighten spinners as this will damage the threads and ears and make them more likely to work loose


Spinners (or knock-on caps)


There are no recommended torque settings for spinners and the exact number of turns will vary from one vehicle to the next.


  • A spinner should be fitted with the wheel jacked up off the ground so that the hub, wheel and spinner are all centralised.
  • Apply the spinner by hand and tighten 3 to 3½ turns; give the spinner a couple of taps with the hammer; lower the wheel to the ground and give the spinner a couple more taps.
  • As long as the hubs are fitted correctly then the spinners will self-tighten and lock as the car is driving.
  • If you hammer the spinners too enthusiastically then you will deform the thread of the spinner and the hub and they are more likely to work loose.
  • Over-tightening also means that if you ever need to replace either the hub or spinner then you will also need to replace the other part as the deformed thread of the old part will not fit with the new thread.
  • If your spinners keep coming loose then it is probably because the hubs have been fitted on the wrong side. For example, the left hub goes on the left-hand side of the car as you sit in it, not on the left as you look at it from the front.

 

Fitting Bolt-on Wire Wheels


Bolt on wire wheels are fitted to a car in the same way that a standard wheel would be fitted to a car. The wheel options are determined by the P.C.D. (Pitch Circle Diameter) as well as the centre bore, size and back spacing of the wheel. There may be some vehicles, usually kit cars or replicas, that wheels can be supplied for based on their running gear but not listed in the Fitment Guide; please contact us to discuss.
 
All MWS bolt-on wire wheels are supplied with a centre cap, retaining nuts and a wrench to tighten the bolts. Replacement accessories are available from stock.

For bolt-on wheels the recommended torque is 75 ft lb but may vary depending on the vehicle.


UK Sales: 01753 549 360
UK Fax: 01753 547 170
  • Italian
  • German
  • french
  • spanish
Export Sales: +44 (0) 1753 598 382
Motor Wheel Service International Ltd, Units 1-4 Elder Way, Waterside Drive, Langley, Slough, Berkshire, SL3 6EP, UK
Sitemap | Webmaster | Contact Us | Terms and Conditions | Powered by vcGenius